Konfigurationsalternativ

cfg

Ändra konfigurationer som redan har ställts in

1

device

Skicka kommando till anslutna mätare

1

factoryreset

Återställ alla inställningar till fabriksinställningarna

3

fwupdate

Uppdatera produktens mjukvara

2

get

Läs ett konfigurationsnyckelsvärde

1

install

Sök efter och installera mätare

1

login

Logga in via konsol eller SMS-läge

1

maintenance

Underhållsuppgift

1

momreport

Läs av momentana värden från installerade mätare och skicka rapport

1

qset

Quick set-konfiguration

1

reboot

Starta om produkten

1

report

Användardefinierbar rapport

1

report1

Användardefinierbar rapport 1

1

report2

Användardefinierbar rapport 2

1

report3

Användardefinierbar rapport 3

1

report4

Användardefinierbar rapport 4

1

report5

Användardefinierbar rapport 5

1

set

Ställ in en konfigurationsnyckel

1

sch

Schemalägg ett kommando

1

status

Få statusinformation från produkten

1

storevalue

Läs och lagra värden på installerade mätare

1

sysreport

Efterfråga en systemrapport

1

logreport

Efterfråga en loggrapport

1

sync

Synkronisera konfigurationen med servern

2

timesync

Synkronisera tidsinställningar med internettidsserver

1

fwupdateevent

Utförs vid uppdatering av produktens mjukvara och rapport skickas

1

rebootevent

Körs vid oväntad omstart och skickar rapport

1

swupdateevent

Utförs vid uppdatering av produktprogramvara och skickar rapport

1

swupdatesynchandler

Körs vid uppdatering av produktprogramvara och startar processen för konfigurationssynkronisering

1

[en] csd.timeout

[en] Idle timeout. Time in seconds before hanging up inactive call.

60

[en] Numeric:

0-86400

1

[en] csd.tmbus.baud

[en] M-Bus baud rate for transparent M-Bus service.

2400

[en] Numeric:

2400, 9600

1

[en] csd.tmbus.packing.interval

[en] Packing interval. Time of inactivity in milliseconds that needs to pass on the M-Bus line before the product transmits information received to the mobile network.

1000

[en] Numeric:

0-65535

1

[en] csd.tmbus.packing.interval

[en] By setting the packing mode to “mbus”, the CMe2100/CMi2110/CMe2130 will make sure that all data transmitted follows the M-Bus protocol. If setting the packing mode to “transparent” the data will be transmitted to the M-Bus without such a control.

mbus

[en] Enumeration:

[en] mbus, transparent

1

[en] csd.mode

[en] GSM data service mode. The product supports transparent M-Bus mode and console application mode.

Tmbus

[en] Enumeration:

[en] tmbus, console

1

[en] csd.enabled

[en] Status of GSM data service. Can be activated or deactivated.

[en] True

[en] Boolean:

[en] true, false

1

[en] csd.speed

[en] GSM bearer control, i.e. the transmission speed on the GSM network.

[en] 0 = Autobauding

[en] 1 = 300 bps (V.21)

[en] 2 = 1200 bps (V.22)

[en] 4 = 2400 bps (V.22bis)

[en] 6 = 4800 bps (V.32)

[en] 7 = 9600 bps (V.32)

[en] 14 = 14400 bps (V.34)

[en] 65 = 300 bps (V.110)

[en] 66 = 1200 bps (V.110)

[en] 68 = 2400 bps (V.110)

[en] 70 = 4800 bps (V.110)

[en] 71 = 9600 bps (V.110)

[en] 75 = 14400 bps (V.110)

0

[en] Numeric:

0, 1, 2, 4, 6, 7, 14, 65, 66, 68, 70, 71, 75

1

[en] tcp.tmbus1.enabled

[en] Status of transparent M-Bus TCP service 1.

[en] False

[en] Boolean:

[en] true, false

1

[en] tcp.tmbus1.baud

[en] Baud rate of transparent M-Bus TCP service 1.

2400

[en] Numeric:

2400, 9600

1

[en] tcp.tmbus1.packing.interval

[en] Packing interval for transparent M-Bus TCP service 1. Time of inactivity in milliseconds that needs to pass on the M-Bus line before the product transmits information.

1000

[en] Numeric:

0-65535

1

[en] tcp.tmbus1.packing.mode

[en] By setting the packing mode to “mbus”, the CMe2100/CMi2110/CMe2130 will make sure that all data transmitted follows the M-Bus protocol. If setting the packing mode to transparent the data will be transmitted to the M-Bus without such a control.

mbus

[en] Enumeration:

[en] mbus, transparent

1

[en] tcp.tmbus1.timeout

[en] The port used for transparent M-Bus TCP service 1.

300

[en] Numeric:

0-65535

1

[en] tcp.tmbus1.timeout

[en] Idle timeout for transparent M-Bus TCP service 1. The time of inactivity in seconds that needs to pass before the TCP connection is closed.

60

[en] Numeric:

0-86400

1

[en] tcp.tmbus2.enabled

[en] Status of Transparent M-Bus TCP service 2. Can be activated or deactivated.

[en] False

[en] Boolean:

[en] true, false

1

[en] tcp.tmbus2.baud

[en] Baud rate of transparent M-Bus TCP service 2.

2400

[en] Numeric:

2400, 9600

1

[en] tcp.tmbus2.packing.interval

[en] Packing interval for transparent M-Bus TCP service 2. Time of inactivity in milliseconds that needs to pass on the M-Bus line before the product transmits information received.

1000

[en] Numeric:

0-65535

1

[en] tcp.tmbus2.packing.mode

[en] By setting the packing mode to mbus, the CMe2100/CMi2110/CMe2130 will make sure that all data transmitted follows the M-Bus protocol. If setting the packing mode to “transparent” the data will be transmitted to the M-Bus without such a control.

mbus

[en] Enumeration:

[en] mbus, transparent

1

[en] tcp.tmbus2.port

[en] The port used for transparent M-Bus TCP service 2.

2400

[en] Numeric:

0-65535

1

[en] tcp.tmbus2.timeout

[en] Idle timeout for transparent M-Bus TCP service 1. The time of inactivity in seconds that needs to pass before the TCP connection is closed.

60

[en] Numeric:

0-86400

1

[en] tcp.console.enabled

[en] Status of TCP console service. Can be activated or deactivated.

[en] False

[en] Boolean:

[en] true, false

1

[en] tcp.console.port

[en] Port used for TCP console service.

9999

[en] Numeric:

0-65535

1

[en] tcp.console.timeout

[en] Idle timeout for the TCP console service 1. The time of inactivity in seconds that needs to pass before the TCP connection is closed.

60

[en] Numeric:

0-86400

1

[en] security.nraccesslist

[en] List of phone numbers that will be able to access the product via SMS and GSM.

[en] Blank

[en] Enumeration:

[en] List of phone numbers

1

[en] security.ipaccesslist

[en] List of IP addresses that will be able to access the product via the TCP services.

[en] Blank

[en] Enumeration:

[en] List of IP addresses

1

[en] security.password1

[en] Password to access level 1 features of the products.

[en] Blank

[en] Text:

[en] 0-8 characters

1

[en] security.password2

[en] Password to access level 2 features of the products.

2222

[en] Text:

[en] 0-8 characters

2

[en] security.password3

[en] Password to access level 2 features of the products.

3333

[en] Text:

[en] 0-8 characters

3

[en] net.autosmtp

[en] Auto detection of SMTP server.

[en] true

[en] Boolean:

[en] true, false

1

[en] net.autoapn

[en] Auto detection of APN settings to be used.

[en] true

[en] Boolean:

[en] true, false

1

[en] net.apn

[en] APN settings to be used by the CMe2100/CMi2110/CMe2130. Setting this parameter will disable the automatic detection of APN.

[en] Blank

[en] Text

1

[en] net.user

[en] APN user name. If APN auto detection is enabled, the username will be set automatically.

[en] Blank

[en] Text

1

[en] net.password

[en] APN password. If APN auto detection is enabled, the password will be set automatically.

[en] Blank

[en] Text

1

[en] net.dns1

[en] DNS server 1. If APN auto detection is enabled, it will be set automatically.

[en] Blank

[en] Text

1

[en] net.dns2

[en] DNS server 2. If APN auto detection is enabled, it will be set automatically.

[en] Blank

[en] Text

1

[en] net.timeout

[en] The time in seconds of inactivity before a network session is closed. Setting the parameter to zero will disable it. Only usable when running listening TCP services on public static IP addresses.

60

[en] Numeric:

0-86400

1

[en] net.cusd.enabled

[en] Used to enable or disable unstructured network data. Must be enabled to be able to request SIM card credit balance information from the CMe2100/CMi2110/CMe2130.

[en] false

[en] Boolean:

[en] true, false

1

[en] device.mbus.searchmode

[en] Sets the way meter are addressed on the M-Bus.

[en] secondary, primary (second choice)

[en] Enumeration:

[en] secondary, primary, esecondary

1

[en] device.mbus.searchstart

[en] The start address used by the CMe2100/CMi2110/CMe2130 when performing a primary meter search.

0

[en] Numeric:

0-250

1

[en] device.mbus.searchend

[en] The end address used by the CMe2100/CMi2110/CMe2130 when performing a primary meter search.

250

[en] Numeric:

0-250

1

[en] device.mbus.searchidmask

[en] Search identification mask when using the secondary addressing mode.

[en] FFFFFFFF

[en] 8 character hex decimal format:

[en] 00000000-FFFFFFFF

2

[en] device.mbus.esearchidmask

[en] Search identification mask when using the enhanced secondary addressing mode.

[en] FFFFFFFF

[en] 8 character hex decimal format:

[en] 00000000-FFFFFFFF

2

[en] device.mbus.searchmanmask

[en] Search manufacturer mask when using the secondary addressing mode.

[en] FFFF

[en] 4 character hex decimal format:

[en] 0000-FFFF

2

[en] device.mbus.esearchmanmask

[en] Search manufacturer mask when using the enhanced secondary addressing mode.

[en] FFFF

[en] 4 character hex decimal format:

[en] 0000-FFFF

2

[en] device.mbus.searchgenmask

[en] Search generation mask when using the secondary addressing mode.

[en] FF

[en] 2 character hex decimal format:

[en] 00-FF

2

[en] device.mbus.esearchgenmask

[en] Search generation mask when using the enhanced secondary addressing mode.

[en] FF

[en] 2 character hex decimal format:

[en] 00-FF

2

[en] device.mbus.searchmedmask

[en] Search medium mask when using the secondary addressing mode.

[en] FF

[en] 2 character hex decimal format:

[en] 00-FF

2

[en] device.mbus.esearchmedmask

[en] Search medium mask when using the enhanced secondary addressing mode.

[en] FF

[en] 2 character hex decimal format:

[en] 00-FF

2

[en] device.mbus.searchbaud

[en] The baud rate used when addressing meters on the M-Bus.

2400

[en] Enumeration:

2400, 9600

1

[en] device.mbus.buswatch

[en] Collision detection of meters.

[en] true

[en] Boolean:

[en] true, false

2

[en] device.mbus.busrecoverytime

[en] Time in milliseconds before a reattempt after a collision has been detected on the M-Bus.

3000

[en] Numeric:

500-15000

2

[en] device.mbus.idleduration

[en] Time in milliseconds of inactivity that needs to pass on the M-Bus before a communication attempt is initiated.

700

[en] Numeric:

500-15000

2

[en] device.mbus.nkesleep

[en] Time in milliseconds after SND_NKE has been sent that needs to pass before a new request.

10000

[en] Numeric:

500-15000

2

[en] device.mbus.responsetimeout

[en] Time in milliseconds that the CMe2100/CMi2110/CMe2130 will wait for a response after making a request on the M-Bus.

300

[en] Numeric:

0-15000

2

[en] device.mbus.fcbmode

[en] By enabling the FCB bit, meters will be read until no more data is found or the multi telegram read limit is reached.

[en] false

[en] Boolean:

[en] true, false

2

[en] device.mbus.telegramcount

[en] Maximum number of telegrams that the CMe2100/CMi2110/CMe2130 will receive during a readout. Requires the FCB bit to be enabled.

0

[en] Numeric:

0-255

2

[en] device.mbus.requestretry

[en] Maximum number of retry attempts when making a request on the M-Bus.

3

[en] Numeric:

0-10

1

[en] device.mbus.selectretry

[en] Maximum number of retries when attempting to address a meter using the secondary addressing mode.

3

[en] Numeric:

0-10

1

[en] device.mbus.maxdevices

[en] Maximum number of meters that the CMe2100/CMi2110/CMe2130 will install. Setting the parameter to -1 will disable it.

-1

[en] Numeric:

-1-250

1

[en] device.mbus.clean

[en] All previously installed meter will be cleared when performing a new meter installation.

[en] false

[en] Boolean:

[en] true, false

1

[en] device.mbus.keepstatus

[en] No changes of status are made when running the installation command.

[en] false

[en] Boolean:

[en] true, false

1

[en] device.mbus.searchbusrecoverytime

[en] Time in milliseconds of inactivity that needs to pass after a collision has been detected during a meter search before a new attempt is performed.

700

[en] Numeric:

500-15000

2

[en] device.mbus.searchidleduration

[en] The minimum number of milliseconds between two requests on the M-Bus when searching for meters.

700

[en] Numeric:

500-15000

2

[en] device.mbus.searchnkesleep

[en] Time in milliseconds after SNK_NKE has been sent before a new request is sent when searching for meters.

10000

[en] Numeric:

500-15000

2

[en] device.mbus.searchresponsetimeout

[en] The time in milliseconds the CMe2100/CMi2110/CMe2130 will wait for a response for a request when searching for meters.

300

[en] Numeric:

0-15000

2

[en] device.mbus.searchrequestretry

[en] Maximum number of retries when making a request on the M-Bus during the meter search process.

0

[en] Numeric:

0-10

1

[en] device.mbus.searchselectretry

[en] Maximum number of retries when selecting a meter during the meter search process.

0

[en] Numeric:

0-10

[en] device.command.runbeforesleep

[en] Number of milliseconds the CMe2100/CMi2110/CMe2130 will wait before communicating on the M-Bus after performing a runbefore command.

2500

[en] Numeric:

0-15000

[en] sms.response.mode

[en] The response modes used by the CMe2100/CMi2110/CMe2130 to inform about the status of requested actions. Decide which status updates the device should inform about.

[en] All

[en] Enumeration:

[en] all, none, progress, error, success, login, source, invalid

1

[en] sms.response

[en] Makes the CMe2100/CMi2110/CMe2130 respond to commands sent by SMS.

[en] true

[en] Boolean:

[en] true, false

1

[en] sms.to

[en] The SMS recipient list. The phone number on the list will receive all requested SMS Push Reports.

[en] Blank

[en] List of phone numbers

1

[en] email.to

[en] The e-mail recipient list. The addresses on the list will receive all requested e-mail Push Reports.

[en] Blank

[en] List of e-mail addresses

1

[en] email.cc

[en] The e-mail copy recipient list. The addresses on the list will receive a copy of all requested e-mail Push Reports.

[en] Blank

[en] List of e-mail addresses

1

[en] email.bcc

[en] The e-mail hidden copy recipient list. The addresses on the list will receive a hidden copy of all requested e-mail Push Reports.

[en] Blank

[en] List of e-mail addresses

1

[en] email.server

[en] The SMTP server that will be used when sending e-mail Push Reports.

[en] Blank

[en] Text

1

[en] email.port

[en] The port number that will be used when connecting to the SMTP server to send e-mail Push Reports.

25

0-65535

1

[en] email.user

[en] Username to be used when connecting to the SMTP server to send e-mail Push Reports.

[en] Blank

[en] Text

1

[en] email.password

[en] Password to be used when connecting to the SMTP server to send e-mail Push Reports.

[en] Blank

[en] Text

1

[en] email.from

[en] The e-mail address from which e-mail Push Reports will be sent.

[en] Blank

[en] Text

1

[en] email.timeout

[en] Time in milliseconds of inactivity that needs to pass before the connection with the SMTP server is closed. Setting the parameter to -1 will implement default settings.

-1

[en] Numeric:

-1-86400

1

[en] email.ssl

[en] Enables SSL connection

[en] false

[en] Boolean:

[en] true, false

1

[en] ftp.server

[en] The FTP/FTPS server to which FTP Push Reports will be sent.

[en] Blank

[en] Text

1

[en] ftp.port

[en] The port used to connect to the FTP/FTPS server when sending FTP Push Reports.

21

[en] Numeric:

0-65535

1

[en] ftp.user

[en] Username used when connecting to the FTP/FTPS server to send FTP Push Reports.

[en] Blank

[en] Text

1

[en] ftp.password

[en] Password used when connecting to the FTP/FTPS server to send FTP Push Reports.

[en] Blank

[en] Text

1

[en] ftp.remotedir

[en] Remote subdirectory to put files when delivering FTP Push Reports.

[en] Blank

[en] Text. Front slash (/) used as separator of directories.

1

[en] ftp.timeout

[en] The time in milliseconds that needs to pass before connection with an FTP/FTPS server is closed. Setting the parameter to -1 will use default settings.

-1

[en] Numeric:

-1-86400

1

[en] ftp.ssl

[en] Enables SSL connection for FTPS.

[en] False

[en] Boolean:

[en] true, false

1

[en] ftp.ssl.explicit

[en] Enable explicit FTPS

[en] False

[en] Boolean:

[en] true, false

1

[en] http.url

[en] The URL for the HTTPSserver where HTTP Push Reports will be sent.

[en] Blank

[en] Text

1

[en] http.tls.verify

[en] Set true for enabling TLS.

[en] Blank

[en] Boolean:

[en] true, false

1

[en] http.user

[en] The username used when connection to the HTTP server to send HTTP Push Reports.

[en] Blank

[en] Text

1

[en] http.password

[en] The password used when connecting to the HTTP server to send HTTP Push Reports.

[en] Blank

[en] Text

1

[en] http.authmode

[en] Enables HTTP server authentication mode, which will have the CMe2100/CMi2110/CMe2130 authenticate itself towards the server before sending a HTTP Push Report.

[en] None

[en] Enumeration:

[en] none, basic

1

[en] http.header

[en] User definable headers to be sent along with HTTP requests. Each one must be separated by a comma.

[en] Blank

[en] Text. <header name>=<header value>

1

[en] time.mode

[en] The type of time server to synchronize the product’s time with.

[en] NTP

[en] Enumeration:

[en] NTP, daytime

1

[en] time.utcoffset

[en] The difference in hours from the coordinated universal time.

1

[en] Numeric:

-11-11

1

[en] time.acceptdiff

[en] The maximum number of seconds that the product is allowed to differ from the time synchronization server.

60

0-86400

1

[en] time.ntp.server

[en] NTP server used by the CMe2100/CMi2110/CMe2130 to synchronize the time.

[en] Se.pool.ntp.org

[en] Arbitrary server address

1

[en] time.ntp.retry

[en] The maximum number of retries the CMe2100/CMi2110/CMe2130 will perform when attempting to synchronize the time with the NTP server.

3

[en] Numeric:

0-10

1

[en] time.ntp.port

[en] The port used when connecting to the NTP server.

123

[en] Numeric:

0-65535

1

[en] time.ntp.localport

[en] The local port used when connecting to the NTP server.

7000

[en] Numeric:

0-65535

1

[en] time.ntp.timeout

[en] The number of seconds of inactivity that needs to pass before a connection with the NTP server is closed. Setting the parameter to -1 will disable it.

10

[en] Numeric:

-1-60

1

[en] time.daytime.server

[en] Daytime server used by the CMe2100/CMi2110/CMe2130 to synchronize the time.

64.236.96.53

[en] Arbitrary server address

1

[en] time.daytime.retry

[en] The maximum number of retries the CMe2100/CMi2110/CMe2130 will perform when attempting to synchronize the time with the daytime server.

3

[en] Numeric:

0-10

1

[en] time.daytime.port

[en] The port used when connecting to the daytime server.

13

[en] Numeric:

0-65535

1

[en] time.daytime.timeout

[en] The number of seconds of inactivity that needs to pass before a connection with the daytime server is closed. Setting the parameter to -1 will disable it.

60

[en] Numeric:

1-60

1

[en] schedule.retrymax

[en] The maximum number of retries that the CMe2100/CMi2110/CMe2130 will perform for a scheduled job.

3

[en] Numeric:

0-10

1

[en] schedule.retryoffset

[en] Time in seconds between each retry attempt for a scheduled job.

60

[en] Numeric:

0-86400

1

[en] syslog.level

[en] The minimum severity level of the events that are saved in the system log.

0

[en] Numeric:

-1-4

1

[en] product.name

[en] The name used by the product to identify itself.

[en] Blank

[en] Text

1

[en] product.culture

[en] The language of the product.

[en] en

[en] Enumeration:

[en] en

1

[en] product.culture.decimalseparator

[en] Character used as decimal separator in Push Reports.

,

[en] Arbitrary character

1

[en] system.cota.urlbase

[en] Configuration synchronization server base URL. Internally detected if not set.

[en] Blank

[en] Text

3

[en] system.cota.url

[en] Configuration synchronization server URL. Internally detected if not set.

[en] Blank

[en] Text

1

[en] system.cota.user

[en] Configuration synchronization server used. Internally detected if not set.

[en] Blank

[en] Text

1

[en] system.cota.password

[en] Configuration synchronization server password. Internally detected if not set.

[en] Blank

[en] Text

1

[en] system.cota.authmode

[en] Configuration synchronization server authentication mode. Internally detected if not set.

[en] Blank

[en] Enumeration:

[en] None, basic

1

[en] branding.company

[en] Company name

[en] Blank

[en] Text

2

[en] branding.adress1

[en] Address line 1

[en] Blank

[en] Text

2

[en] branding.address2

[en] Address line 2

[en] Blank

[en] Text

2

[en] branding.address3

[en] Address line 3

[en] Blank

[en] Text

2

[en] branding.address4

[en] Address line 4

[en] Blank

[en] Text

2

[en] branding.tel1

[en] Telephone number 1

[en] Blank

[en] Text

2

[en] branding.tel2

[en] Telephone number 2

[en] Blank

[en] Text

2

[en] branding.fax1

[en] Fax number

[en] Blank

[en] Text

2

[en] branding.email

[en] E-mail address

[en] Blank

[en] Text

2

[en] branding.web

[en] Web address

[en] Blank

[en] Text

2

[en] branding.logourl

[en] URL to logo

[en] Blank

[en] Text

2

[en] branding.logoalt

[en] Alternative text if logo is not found

[en] Blank

[en] Text

2

[en] branding.supportinfo

[en] Support information text

[en] Blank

[en] Text

2

[en] branding.supporttel

[en] Support telephone number

[en] Blank

[en] Text

2

[en] branding.supportemail

[en] Support e-mail address

[en] Blank

[en] Text

2

[en] monitor.enabled

[en] Enables monitor handling

[en] false

[en] Boolean:

[en] true, false

1

[en] enabled

[en] Enables a schedule or report

-

[en] Boolean:

[en] true, false

1

[en] cron

[en] Cron schedule for schedulable events

-

[en] Cron pattern

1

[en] runonerror

[en] Runs when the specific command errors

-

[en] Arbitrary command

1